Oldham Combustible Gas - Catalytic (Lel) Replacement Sensor For Itrans And Itrans 2

The Oldham iTrans fixed-point gas monitor employs an intelligent electronics platform to provide one or two points of detection from a single head for maximum flexibility, superior performance and lower installation costs.

Oldham Itrans 2 Nh3 Gas Detector, (4-20 Ma Output: 0 -500 Ppm)

Oldham iTrans 2 Fixed Gas Detector with electrochemical smart sensor for Ammonia (NH3) 0-500ppm. 4-20mA optional RS-485 Modbus/HART and 3 alarm relay outputs. Explosion-proof NEMA 4X Enclosure. IP66. CSA, ATEX and IECEx Approvals.

Specifications

Oldham Bm25 Sensor, O2 (Oxygen 0-30% Vol.), Medium

The Oldham BM 25 Transportable Multi-Gas Area Monitor combines the advantages of a fixed gas detection area monitor with the transportable qualities of a portable instrument.

Key Features

• Up to 5 gases simultaneously
• 103 dB at 3 feet audible alarm
• Ultra-bright flashing signal at 360deg

Specifications

•  Run time of 170 hours
• • Resistant to harsh environment
• • Easily transportable - less than 15 lbs
• • 30 devices per network
• • 16 independent networks
• • More than 0.5 mile RF line of site

The Oldham BM 25 can detect between one and five gases, and is used for applications such as team protection, area surveillance, mobile or temporarily work applications and also locations where a permanent, fixed system is not suitable.

Up to 170 hours of continuous running time are possible with the Oldham BM 25, as it is powered by a NiMH battery pack.

The Oldham BM 25 monitor also has datalogging capacity of more than four months, as well as STEL and TWA values.

The protection of larger areas can be achieved using multiple units, which can be grouped using optional alarm transfer kits. Alarms are transferred from one BM 25 to the next. For long-term area monitoring in classified zones, an intrinsically safe trickle charger is also available.

Available as an option, the radio communication allows several BM 25 devices to communicate on the same network or to send information wirelessly to a controller.

The network topology used by the BM 25 is a MESH network. In a mesh network all hosts are connected peerto- peer without central hierarchy, thereby forming a net-like structure. Consequently, each node can receive, send and relay data. This prevents having sensitive points, which in case of failure, cut the connection of the network. If a node is down, its goes through another route.

Wireless communication is made via a 2.4 GHz radio and emitted power is less than 100 mW. Maximum distance between two communicating devices is 0.6 mile line of sight.

Mesh topology allows fast and simple deployment, high coverage versatility and high fault tolerance. It significantly reduces installation and operating costs of networks. These solutions reproduce the architecture of the Internet while optimizing for wireless.

The Oldham BM 25 Transportable Multi-Gas Area Monitor is suitable for a wide range of industries including refineries and pharmaceutical production. Applications suitable for the Oldham BM 25 include turnaround work sites, rig overhauls and fence-line surveillance.

"Plug-and-Play" Sensors Available: O2, CO, H2S, %LEL, SO2, NO, NO2, HCN, HCl, Cl2, ETO, PH3, AsH3, SiH4, CO2, H2, NH3, PID, XP IR, etc.

Oldham Bm25 Sensor, Co (Carbon Monoxide 0-1000Ppm), Mini

The Oldham BM 25 Transportable Multi-Gas Area Monitor combines the advantages of a fixed gas detection area monitor with the transportable qualities of a portable instrument.

Key Features

• Up to 5 gases simultaneously
• 103 dB at 3 feet audible alarm
• Ultra-bright flashing signal at 360deg

Specifications

•  Run time of 170 hours
• • Resistant to harsh environment
• • Easily transportable - less than 15 lbs
• • 30 devices per network
• • 16 independent networks
• • More than 0.5 mile RF line of site

The Oldham BM 25 can detect between one and five gases, and is used for applications such as team protection, area surveillance, mobile or temporarily work applications and also locations where a permanent, fixed system is not suitable.

Up to 170 hours of continuous running time are possible with the Oldham BM 25, as it is powered by a NiMH battery pack.

The Oldham BM 25 monitor also has datalogging capacity of more than four months, as well as STEL and TWA values.

The protection of larger areas can be achieved using multiple units, which can be grouped using optional alarm transfer kits. Alarms are transferred from one BM 25 to the next. For long-term area monitoring in classified zones, an intrinsically safe trickle charger is also available.

Available as an option, the radio communication allows several BM 25 devices to communicate on the same network or to send information wirelessly to a controller.

The network topology used by the BM 25 is a MESH network. In a mesh network all hosts are connected peerto- peer without central hierarchy, thereby forming a net-like structure. Consequently, each node can receive, send and relay data. This prevents having sensitive points, which in case of failure, cut the connection of the network. If a node is down, its goes through another route.

Wireless communication is made via a 2.4 GHz radio and emitted power is less than 100 mW. Maximum distance between two communicating devices is 0.6 mile line of sight.

Mesh topology allows fast and simple deployment, high coverage versatility and high fault tolerance. It significantly reduces installation and operating costs of networks. These solutions reproduce the architecture of the Internet while optimizing for wireless.

The Oldham BM 25 Transportable Multi-Gas Area Monitor is suitable for a wide range of industries including refineries and pharmaceutical production. Applications suitable for the Oldham BM 25 include turnaround work sites, rig overhauls and fence-line surveillance.

"Plug-and-Play" Sensors Available: O2, CO, H2S, %LEL, SO2, NO, NO2, HCN, HCl, Cl2, ETO, PH3, AsH3, SiH4, CO2, H2, NH3, PID, XP IR, etc.

Oldham Bm25 Sensor, H2S (Hydrogen Sulfide 0-100Ppm), Mini

The Oldham BM 25 Transportable Multi-Gas Area Monitor combines the advantages of a fixed gas detection area monitor with the transportable qualities of a portable instrument.

Key Features

• Up to 5 gases simultaneously
• 103 dB at 3 feet audible alarm
• Ultra-bright flashing signal at 360deg

Specifications

•  Run time of 170 hours
• • Resistant to harsh environment
• • Easily transportable - less than 15 lbs
• • 30 devices per network
• • 16 independent networks
• • More than 0.5 mile RF line of site

The Oldham BM 25 can detect between one and five gases, and is used for applications such as team protection, area surveillance, mobile or temporarily work applications and also locations where a permanent, fixed system is not suitable.

Up to 170 hours of continuous running time are possible with the Oldham BM 25, as it is powered by a NiMH battery pack.

The Oldham BM 25 monitor also has datalogging capacity of more than four months, as well as STEL and TWA values.

The protection of larger areas can be achieved using multiple units, which can be grouped using optional alarm transfer kits. Alarms are transferred from one BM 25 to the next. For long-term area monitoring in classified zones, an intrinsically safe trickle charger is also available.

Available as an option, the radio communication allows several BM 25 devices to communicate on the same network or to send information wirelessly to a controller.

The network topology used by the BM 25 is a MESH network. In a mesh network all hosts are connected peerto- peer without central hierarchy, thereby forming a net-like structure. Consequently, each node can receive, send and relay data. This prevents having sensitive points, which in case of failure, cut the connection of the network. If a node is down, its goes through another route.

Wireless communication is made via a 2.4 GHz radio and emitted power is less than 100 mW. Maximum distance between two communicating devices is 0.6 mile line of sight.

Mesh topology allows fast and simple deployment, high coverage versatility and high fault tolerance. It significantly reduces installation and operating costs of networks. These solutions reproduce the architecture of the Internet while optimizing for wireless.

The Oldham BM 25 Transportable Multi-Gas Area Monitor is suitable for a wide range of industries including refineries and pharmaceutical production. Applications suitable for the Oldham BM 25 include turnaround work sites, rig overhauls and fence-line surveillance.

"Plug-and-Play" Sensors Available: O2, CO, H2S, %LEL, SO2, NO, NO2, HCN, HCl, Cl2, ETO, PH3, AsH3, SiH4, CO2, H2, NH3, PID, XP IR, etc.

Oldham Bm 25 Sensor, O2 (Oxygen 0-30% Vol.) Mini

The Oldham BM 25 Transportable Multi-Gas Area Monitor combines the advantages of a fixed gas detection area monitor with the transportable qualities of a portable instrument.

Key Features

• Up to 5 gases simultaneously
• 103 dB at 3 feet audible alarm
• Ultra-bright flashing signal at 360deg

Specifications

•  Run time of 170 hours
• • Resistant to harsh environment
• • Easily transportable - less than 15 lbs
• • 30 devices per network
• • 16 independent networks
• • More than 0.5 mile RF line of site

The Oldham BM 25 can detect between one and five gases, and is used for applications such as team protection, area surveillance, mobile or temporarily work applications and also locations where a permanent, fixed system is not suitable.

Up to 170 hours of continuous running time are possible with the Oldham BM 25, as it is powered by a NiMH battery pack.

The Oldham BM 25 monitor also has datalogging capacity of more than four months, as well as STEL and TWA values.

The protection of larger areas can be achieved using multiple units, which can be grouped using optional alarm transfer kits. Alarms are transferred from one BM 25 to the next. For long-term area monitoring in classified zones, an intrinsically safe trickle charger is also available.

Available as an option, the radio communication allows several BM 25 devices to communicate on the same network or to send information wirelessly to a controller.

The network topology used by the BM 25 is a MESH network. In a mesh network all hosts are connected peerto- peer without central hierarchy, thereby forming a net-like structure. Consequently, each node can receive, send and relay data. This prevents having sensitive points, which in case of failure, cut the connection of the network. If a node is down, its goes through another route.

Wireless communication is made via a 2.4 GHz radio and emitted power is less than 100 mW. Maximum distance between two communicating devices is 0.6 mile line of sight.

Mesh topology allows fast and simple deployment, high coverage versatility and high fault tolerance. It significantly reduces installation and operating costs of networks. These solutions reproduce the architecture of the Internet while optimizing for wireless.

The Oldham BM 25 Transportable Multi-Gas Area Monitor is suitable for a wide range of industries including refineries and pharmaceutical production. Applications suitable for the Oldham BM 25 include turnaround work sites, rig overhauls and fence-line surveillance.

"Plug-and-Play" Sensors Available: O2, CO, H2S, %LEL, SO2, NO, NO2, HCN, HCl, Cl2, ETO, PH3, AsH3, SiH4, CO2, H2, NH3, PID, XP IR, etc.

Oldham Bm 25 Sensor, Co/H2S (Carbon Monoxide/Hydrogen Sulfide), Medium

The Oldham BM 25 Transportable Multi-Gas Area Monitor combines the advantages of a fixed gas detection area monitor with the transportable qualities of a portable instrument.

Key Features

• Up to 5 gases simultaneously
• 103 dB at 3 feet audible alarm
• Ultra-bright flashing signal at 360deg

Specifications

•  Run time of 170 hours
• • Resistant to harsh environment
• • Easily transportable - less than 15 lbs
• • 30 devices per network
• • 16 independent networks
• • More than 0.5 mile RF line of site

The Oldham BM 25 can detect between one and five gases, and is used for applications such as team protection, area surveillance, mobile or temporarily work applications and also locations where a permanent, fixed system is not suitable.

Up to 170 hours of continuous running time are possible with the Oldham BM 25, as it is powered by a NiMH battery pack.

The Oldham BM 25 monitor also has datalogging capacity of more than four months, as well as STEL and TWA values.

The protection of larger areas can be achieved using multiple units, which can be grouped using optional alarm transfer kits. Alarms are transferred from one BM 25 to the next. For long-term area monitoring in classified zones, an intrinsically safe trickle charger is also available.

Available as an option, the radio communication allows several BM 25 devices to communicate on the same network or to send information wirelessly to a controller.

The network topology used by the BM 25 is a MESH network. In a mesh network all hosts are connected peerto- peer without central hierarchy, thereby forming a net-like structure. Consequently, each node can receive, send and relay data. This prevents having sensitive points, which in case of failure, cut the connection of the network. If a node is down, its goes through another route.

Wireless communication is made via a 2.4 GHz radio and emitted power is less than 100 mW. Maximum distance between two communicating devices is 0.6 mile line of sight.

Mesh topology allows fast and simple deployment, high coverage versatility and high fault tolerance. It significantly reduces installation and operating costs of networks. These solutions reproduce the architecture of the Internet while optimizing for wireless.

The Oldham BM 25 Transportable Multi-Gas Area Monitor is suitable for a wide range of industries including refineries and pharmaceutical production. Applications suitable for the Oldham BM 25 include turnaround work sites, rig overhauls and fence-line surveillance.

"Plug-and-Play" Sensors Available: O2, CO, H2S, %LEL, SO2, NO, NO2, HCN, HCl, Cl2, ETO, PH3, AsH3, SiH4, CO2, H2, NH3, PID, XP IR, etc.

Oldham Bm25 Sensor, Lel/Methane (Bm25 Atex Only)

The Oldham BM 25 Transportable Multi-Gas Area Monitor combines the advantages of a fixed gas detection area monitor with the transportable qualities of a portable instrument.

Key Features

• Up to 5 gases simultaneously
• 103 dB at 3 feet audible alarm
• Ultra-bright flashing signal at 360deg

Specifications

•  Run time of 170 hours
• • Resistant to harsh environment
• • Easily transportable - less than 15 lbs
• • 30 devices per network
• • 16 independent networks
• • More than 0.5 mile RF line of site

The Oldham BM 25 can detect between one and five gases, and is used for applications such as team protection, area surveillance, mobile or temporarily work applications and also locations where a permanent, fixed system is not suitable.

Up to 170 hours of continuous running time are possible with the Oldham BM 25, as it is powered by a NiMH battery pack.

The Oldham BM 25 monitor also has datalogging capacity of more than four months, as well as STEL and TWA values.

The protection of larger areas can be achieved using multiple units, which can be grouped using optional alarm transfer kits. Alarms are transferred from one BM 25 to the next. For long-term area monitoring in classified zones, an intrinsically safe trickle charger is also available.

Available as an option, the radio communication allows several BM 25 devices to communicate on the same network or to send information wirelessly to a controller.

The network topology used by the BM 25 is a MESH network. In a mesh network all hosts are connected peerto- peer without central hierarchy, thereby forming a net-like structure. Consequently, each node can receive, send and relay data. This prevents having sensitive points, which in case of failure, cut the connection of the network. If a node is down, its goes through another route.

Wireless communication is made via a 2.4 GHz radio and emitted power is less than 100 mW. Maximum distance between two communicating devices is 0.6 mile line of sight.

Mesh topology allows fast and simple deployment, high coverage versatility and high fault tolerance. It significantly reduces installation and operating costs of networks. These solutions reproduce the architecture of the Internet while optimizing for wireless.

The Oldham BM 25 Transportable Multi-Gas Area Monitor is suitable for a wide range of industries including refineries and pharmaceutical production. Applications suitable for the Oldham BM 25 include turnaround work sites, rig overhauls and fence-line surveillance.

"Plug-and-Play" Sensors Available: O2, CO, H2S, %LEL, SO2, NO, NO2, HCN, HCl, Cl2, ETO, PH3, AsH3, SiH4, CO2, H2, NH3, PID, XP IR, etc.

Oldham Itrans And Itrans2 Smart Sensor H2S

Replacement Itrans & Itrans2 Smart Sensor Housing Assembly with H2S Hydrogen Sulfide Sensor 0-500 ppm

Oldham Oxygen (O2) Replacement Sensor For Itrans And Itrans 2

Oldham / Industrial Scientific Replacement iTrans & iTrans2 Oxygen (O2) Sensor Replace and repair your iTrans or iTrans2 Fixed System Gas monitor with Oldham Gas Detection's replacement (O2) Oxygen Sensor.

Oldham Hydrogen Sulfide (H2S) Replacement Sensor For Itrans And Itrans2

Repair your Oldham / Industrial Scientific iTrans Fixed System Gas monitor with a new Industrial Scientific's replacement (H2S) Hydrogen Suiflide Sensor.

Oldham 8-Relay Module For Mx 43

3 MX43 versions available

The MX43 gas controler is available in 3 versions to meet the greatest number of applications:

• MX43M-4: 4-line wall version allowing the connection of 4 analog 4-20 mA sensors or up to 16 digital sensors distributed over 4 lines
• MX43M-8: Wall-mounted version 8 lines allowing to connect 8 analog sensors 4-20 mA or up to 32 digital sensors distributed on 8 lines
• MX43R-8: Rack version 19’’ / 4U 8 lines allowing to connect 8 analog sensors 4-20 mA or up to 32 digital sensors distributed on 8 lines

   

Many input/output modules

The MX43 gas detection unit accepts various input/output modules to increase the system's capacities and flexibility.

• Addressable module with 8 analog inputs that can receive all types of 4-20 mA analog transmitters
• Addressable 4 or 8 relay module (+ 2 logic inputs) that can be deported as close as possible to the controls.
• Addressable module with 16 digital inputs that can receive all digital information (emergency stop, limit switch, fire alarm).
• Addressable module with 4 analog outputs for connection to a recorder, a PLC, a building management system, etc.

MX43 gas controller main assets

• Up to 32 digital or analog gas detectors
• Large graphic LCD display and customizable views
• 5 alarm levels per measurement channel (Al1, Al2, Al3, and average)
• Logs of the last 512 events (serial) and archives
• measurements and parameters on optional USB stick

Specifications

• Function: Multichannel central measurement and multi-channel alarm
• Dimensions: 370 x 299 x 109 mm (wall box) 483 x 177 x 192.5 mm (19 ”4U rack)
• Protection rating IP55 (wall), IP31 (rack)
• Capacity:
  - Digital lines: 4 detectors per line, 8 lines max., Proprietary RS485 protocol
  - Analog lines: 4-20 mA linear inputs , 8 lines max.
• Power supply: 100-240 Vac 50-60 Hz, consumption 500mA
• Display: Backlit graphic LCD, user-customizable views, bargraph with alarm thresholds indication
• Status indicators: 7 LEDs for each of the 2 lines, 1 power-on indicator and 1 general fault indicator
• Alarms: 5 alarm levels per measurement channel
• Internal relays: 5 programmable potential-free changeover contact relays + 1 fault relay (not configurable)
• Datalogger:
  - As standard, 512 recordings per type of event
  - Optional USB port for measurements and alarms archiving
• Digital output: RS485 Modbus Protocol (optional)
• Cable entry and exit: 12 PE M16 for cables from 4 to 8 mm² & 6 PE M20 for cables from 6 to 12 mm²
• Certifications: EMC: According to EN50270
• Operating temperature: -20 to + 50 ° C

Oldham Itrans And Itrans2 Terminal Power Board With Relays (Itrans Rev.9 Or Above)

The Oldham iTrans fixed-point gas monitor employs an intelligent electronics platform to provide one or two points of detection from a single head for maximum flexibility, superior performance and lower installation costs.

Oldham Itrans And Itrans 2 Terminal Power Board Without Relays (Itrans Rev.9 Or Above)

The Oldham iTrans fixed-point gas monitor employs an intelligent electronics platform to provide one or two points of detection from a single head for maximum flexibility, superior performance and lower installation costs.

Oldham Itrans Main Electronics Board Assembly & Display Module (Itrans Rev.8 Or Below)

The Oldham iTrans fixed-point gas monitor employs an intelligent electronics platform to provide one or two points of detection from a single head for maximum flexibility, superior performance and lower installation costs.

Oldham Itranss And Itrans 2 Main Electronics Board Assembly & Display Module (Itrans Rev.9 Or Above)

The Oldham iTrans fixed-point gas monitor employs an intelligent electronics platform to provide one or two points of detection from a single head for maximum flexibility, superior performance and lower installation costs.

Oldham Itrans And Itrans 2 Calibration Wand

The Oldham iTrans fixed-point gas monitor employs an intelligent electronics platform to provide one or two points of detection from a single head for maximum flexibility, superior performance and lower installation costs.

Oldham Itrans Chassis Without Relays (Itrans Rev.8 Or Below)

The Oldham iTrans fixed-point gas monitor employs an intelligent electronics platform to provide one or two points of detection from a single head for maximum flexibility, superior performance and lower installation costs.

Oldham Replacement Plug-In Ir Combustible Gas Sensor

The Oldham iTrans fixed-point gas monitor employs an intelligent electronics platform to provide one or two points of detection from a single head for maximum flexibility, superior performance and lower installation costs.

Oldham Itrans 2 Lel Gas Detector

Oldham iTrans 2 Stand-Alone Gas Detector with catalytic smart sensor for Combustibles 0-100% LEL. 4-20mA. NEMA 4X/IP66 Enclosure to be installed in safe area only (Non-Explosion Proof, no relays nor Modbus/HART available) Factory configured for Methane or Pentane. Characteristics
Large Sensor Offering – Electrochemical, Catalytic and Infrared
Non-Intrusive Calibration
Smart Sensor
HART (optional)
RS-485 Modbus
Programmable Relays (optional)
Dual Gas Sensing (optional)
Certifications
Oil and Gas Industry
Offshore Drilling
Utilities and Power
Petrochemical Industry
Municipal Water and
Waste Treatment
Food and Beverage Production
Sensors
The iTrans 2 is available with sensors for most common gases including: Infrared, CO 2 , Catalytic Bead Combustible and electrochemical sensors. It can support simultaneous detection from two sensors, either directly attached to the display, or remote sensors.

Versatile
The iTrans 2 can be configured to meet nearly any application through its state-of-the art features and options.
Explosion-proof
HART (optional)
RS-485 Modbus
Stainless Steel Enclosure (optional)
Programmable Relays (optional)
3-wire, 4-wire Installations
Dual Gas Sensing (optional)
Remote Sensing (optional)
Large Sensor Offering – Electrochemical, Catalytic and Infrared
Easy to use
Smart Sensor
Non-Intrusive Calibration
Dual-channel split-screen LED display
Other features and benefits
Dual Gas Sensing: The iTrans 2 can detect and display up to two gases on certain models. Both gas sensors may be mounted directly to the transmitter, or may be mounted remotely.
Wide Sensor Offering: The iTrans 2 supports Electrochemical, Catalytic Bead and Infrared sensors. The iTrans 2 is available for most common industrial gases, allowing of standardization for your gas detection equipment.
Smart Sensors: The iTrans 2‘s smart sensors come factory pre-calibrated and automatically send sensor information, such as sensor life, to the transmitter. A sensor life indicator is displayed immediately after each calibration.
Dual-channel split-screen LED display: For optimum visibility in dark places
Non-Intrusive Calibration: The iTrans 2‘s non-intrusive interface keys operate with a simple magnetic wand and allow for full transmitter configuration and calibration without opening the unit’s explosion-proof housing.
Programmable Relays: The microprocessor-controlled transmitters are capable of independent operation or multi-point system configuration. With optional on-board relays, the monitor has the added ability of stand-alone operation, activating alarms, horns or fans, and can also shut down a system without the need to wire back to a central control panel.
Multiple Wiring Options: The iTrans 2 can be configured to meet almost any installation application. Common configurations includes: 3-Wire (4-20mA) Models - Allow for full utilization of the iTrans 2‘s features and options and can be used with all of the iTrans 2‘s sensors / 4-Wire (Digital ModBus) Models - Allows for full utilization of the iTrans 2‘s features and options and can be used with all of the iTrans 2‘s sensors.
HARTTM Communication Protocol: With the optional HART Communication Protocol, the iTrans 2 offers remote diagnostics, set-up or calibration by super - imposing a high-frequency current across the industry standard 4-20mA analog line.
Stainless Steel Enclosure: An optional stainless steel enclosure for corrosive environments.

Specifications

Oldham Bm 25 Datalink Adapter Kit (Software W/Usb Adapter Cable)

BM25 Datalink Adapter Kit (Software w/USB Adapter Cable) for use with the Oldham BM25 Area Gas Monitor